This article is for student, faculty, and staff seeking information regarding installing the Pulse Secure VPN client on various versions of Linux, and will provide instructions on how to do so.
Issues With Linux Client
There have been reports of recent issues with the VPN client on Linux. Check the file /etc/hotsts and remove any reference to the names vpn.uconn.edu" or sslvpn.uconn.edu. Contact the Technology Support Center if you still experience issues after correcting those entries.
Installing the Pulse Secure Client on Linux
- Download the package installer to the Linux client.
- Visit the Pulse Secure Client page in the UConn Software Catalog to choose your download.
- Run the installer using the commands below. For example, if the Pulse Linux client is saved in /$HOME/downloads on Ubuntu, then the command would be: Sudo dpkg -i /$HOME/downloads/Pulse-linux-9.1r2.0-x64.deb.
- For Debian-based Linux installation (such as Ubuntu): sudo dpkg -i <package name>
- For RPM-based Linux installation (such as CentOS): sudo rpm -ivh <package name>
- The script will prompt the user to install any missing dependent packages if they are not already installed.
- For example, you may get a message similar to the one below:
Please execute below commands to install missing dependent packages manually:
apt-get install lib32z1
apt-get install libc6-i386
apt-get install libwebkitgtk-1.0-0:i386
apt-get install libproxy1:i386
apt-get install libproxy1-plugin-gsettings:i386
apt-get install libproxy1-plugin-webkit:i386
apt-get install libdconf1:i386
apt-get install dconf-gsettings-backend:i386 - Alternatively, you may get a message similar to the one below:
You can install the missing dependency packages by running the below script:
sudo /usr/local/pulse/PulseClient_x86_64.sh install_dependency_packages
- For example, you may get a message similar to the one below:
Launching the Pulse Secure Client
Launching Pulse Secure Client from Installed Applications List
To launch Pulse Secure client from the list of installed applications,
- Locate Pulse Secure in the list of installed applications.
- Create a new connection to vpn.uconn.edu.
- Click Connect, next to New Entry.
- Enter your UConn NetID and password to authenticate.
Launching Pulse Secure Client via CLI
To launch the client via CLI,
- Open a new terminal window.
- Enter the root shell:
~$ sudo –i
[sudo] password for username: password Use the command below to launch the VPN client, substituting NetID with your UConn NetID in lowercase:
root@:~#/usr/local/pulse/pulsesvc -h vpn.uconn.edu -u NetID –r UConnThis command is case sensitive and will only work as entered here.- You will be prompted for a VPN Password. Enter your NetID password. It will not be displayed or saved.
- After the VPN tunnel is created successfully, the terminal window will remain blank and must remain open. If the terminal window is closed, this will close the VPN connection.
- You can check the status of the connection by opening a new terminal window and using the following method:
:~$ ifconfig
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:137.99.170.78 P-t-P:137.99.170.78 Mask:255.255.254.0
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1
RX packets:5 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:500
RX bytes:560 (560.0 B) TX bytes:299 (299.0 B)
7. You can end your VPN session by closing the original terminal window or using crtl+c to end the process.
Related Articles
Filter by label
There are no items with the selected labels at this time.